ENEnglish
AZAzərbaycanca
UZO‘zbekcha
ARالعربية
FRFrançais
DEDeutsch
RUРусский
The flame is extinguished
When the flames are extinguished by a burning liquid or airflow, the safety system must safely cut off the gas.
CE · Household gas hob
CE conformity for Household gas hob
For Household gas hob, the applicable CE scope is determined from intended use, energy sources, safety architecture and target market. The risk assessment, technical file, testing and conformity route must be verified against the actual model.
Use itDon 't cook in open burners in the kitchen or at home
The constructionAncastral, set-top or solo; glass, enamel or stainless steel
Gas routeInlet connection, manifold, faucet/valve, injector and briller
SecurityFire control, safe shutdown and markings to reduce miscommunication
Direct response to the scope
CE conformity for Household gas hob — Define the product boundary first
The technical identity of a home type gas stove is not limited to the number of eyes. The nominal heat input of the burners, the presence of a fast or wok type burner, the electricity or manuality of the ignition, the flame control element, the potter's bearing geometry, and the ancastral ventilation gap change the safety rating. If two different burner families are used on the same glass board, the injector, the air conditioning, and the cross-fire are verified for each eye.
The gas path of the furnace must be non-leakageable from the input manifold and the pipes, from there to the injector and the burner, and resistant to mechanical stresses. When the fire is extinguished, the gas must be cut off before reaching the dangerous accumulation, the safe occurrence of re-ignition, and the failure to move the flame to accessible areas at different bowl sizes are examined. In the Ancustration model, the lower cabinet temperature, nearby wall and counter materials are also reflected in the experiment and installation instructions.
Electrical safety and electromagnetic effects in a model with an electric flare generator, timing or electronic cutting system are assessed according to product configuration; LVD and EMC results are justified by voltage, function, and integrated device structure. When type inspection and serial production monitoring are completed, the manufacturer is responsible for the consistency of the marking, reporting, instructions, and technical file.
Product profile
Technical features that change the evaluation
The following data shows why even models with the same product name can change the path of conformity.
Use itDon 't cook in open burners in the kitchen or at home
The constructionAncastral, set-top or solo; glass, enamel or stainless steel
Gas routeInlet connection, manifold, faucet/valve, injector and briller
SecurityFire control, safe shutdown and markings to reduce miscommunication
Market dataGas family, category of equipment and nominal feed pressure
OptionsElectric ignition, wok eye, conversion kit and child lock
Risk architecture
The main dangers to be addressed in the file
The protective, control and verification approach shall be based on the actual product cycle.
Starting late
If the ignition position and the time to start the gas is delayed, the blister may accumulate a mixture around the burner; the ignition behavior is tested in all eyes.
Warm surface
The temperature of the board, button, container and near-table is measured at normal load; user contact and material strength are evaluated.
Uncertainty of closure
The carrier range and the position of the briller shall be examined to prevent the collapse of the small or large container.
Gas conversion error
The wrong injector, pressure setting or missing label will disrupt the burn; kit parts and service steps should be traceable.
Lack of air conditioning
Instructions are given for the openings, assembly dimensions and connection access to reduce heat and potential leakage accumulation in the lower volume.
The conditional law matrix
When will the regulation take effect?
A single product name doesn't give the same answer for all models.
| The subject | The situation | Product-based evaluation |
|---|---|---|
| GAR 2016/426 | YES, YES | The basic scope of the gas-fired household appliance for cooking is to be applied. |
| Authorized organization | YES, YES | The GAR module requires third party participation in the assessment of the route type and production. |
| LVD | IT 'S A MESS . | If there's an electrical ignition or control, the voltage and the entire product relationship are examined. |
| EMC | IT 'S A MESS . | When electronic control is available, emissions and immune behavior are addressed along with the safety function. |
| The Commission shall adopt implementing acts in accordance with Article 21 of Regulation (EU) No 1095/2014. | YES, YES | The energy efficiency measurement and product information requirements of the household type gas stove are met; energy label 65/2014 is not applicable to gas stove. |
| PED | NO , NOT AT ALL . | Typical household gas feeds do not automatically cover PEDs. |
| ATEX | NO , NOT AT ALL . | The presence of fuel gas in normal household use does not make the product explosive. |
Standard and verification approach
- EN 30-1-1 and EN 30-2-1: The version, scope and current harmonisation status shall be verified for the requirements of general safety and rational energy use in the domestic gas oven.
- EN 437: The gas category is used to define the test gas and experimental pressure.
- EN 13611: When gas control and safety arrangements are in place, they are evaluated as being related to the function of the component.
- Applicable electrical safety standards: The torque is selected according to the actual structure of the generator and the electronic equipment; it does not replace the gas test.
- The applicable EMC standards: Once the home environment and device ports are determined, they are used for emission and immunity testing.
Important distinction
CE conformity for Household gas hob — Product conformity is a separate study.
ISO management system certification does not replace product-specific risk analysis, test evidence and compliance file.
The compliance work plan
In what order will the technical preparation proceed?
Defining the product family
The number of eyes, the briller power, the board, the ignition, the control and the gas options are separated by the model matrix.
Scope and default selection
The GAR and harmonised standard approach are determined to suit the target market gas conditions and the equipment structure.
Sample and experiment preparation
The representative sample is prepared with settings for leakage, ignition, combustion, temperature and stability.
Assessment of the approved organization
Type-examination and verification of the organisation of the selected serial production conformity module shall be carried out.
Statement and serial production control
The EU Statement of Conformity, CE label, instructions and the critical part modification procedure are interlinked.
Product records to search for in the technical file
- Product and model family definitions
- Gas cycle diagram with general location
- Briller, injector and control parts list
- Risk assessment
- Gas category and target country matrix
- Gas safety and energy efficiency experimental reports
- Tagging drawings
- Installation, use, conversion and maintenance instructions
They 're the entries for a healthy offer .
- Model and number of eyes
- Brush forces
- Gas types and categories
- Target countries
- Fire control system
- Current test reports
- Annual production and production sites
The proposal is prepared according to the size of the model family, target gas categories, sample numbers, available evidence and selected production oversight path.
Internal links
Relevant category and product guides
Compare the top coverage or other similar risk architecture.
Frequently Asked Questions
CE conformity for Household gas hob — Technical answers about
What are the duties of the approved entity and the manufacturer in the gas furnace?
The approved entity shall draw up a type or certificate of conformity in the selected module; the manufacturer shall draw up an EU Statement of conformity, apply the CE marking and be responsible for serial production.
Can we use a single furnace for natural gas and LPG?
It is possible if the manufacturer specifies the appropriate category, injector, setting, test and conversion instructions; the user must not change the quality part.
Does every spring need fire safety?
The quality of the product and the design requirements ensure that the loss of flame does not lead to dangerous gas build-up.
Is the glass panel broken under GAR?
The material, heat and mechanical resistance affect the safety of the device; glass breakage should not endanger the gas pathway or the user.
If the anchorage size changes, will the current type remain valid?
If the air conditioning, temperature and component location are affected, the change cannot be assumed to be covered without evaluation of the approved type.
What's the duration of the gas stove test?
A reliable fixed time cannot be given without the number of models, gas categories, sample preparation, repetition of failed experiments and the production module being seen.
Technical scope and offer
CE conformity for Household gas hob — Let us clarify your technical file together.
Share the model of the machine or device, the location of use and the basic technical data. The Kayra Patent explains the path to be followed for scope analysis, technical preparation, test plan and, where necessary, approved organization coordination.
Final inspection of content and technical scope: 20 August 2026The official bases: European Commission Gas burning devices · EUR-Lex — GAR 2016/426