ENEnglish
AZAzərbaycanca
UZO‘zbekcha
ARالعربية
FRFrançais
DEDeutsch
RUРусский
The shape and closure
The rapid locking of the cavity creates crushing for the hand or equipment; doors must cut off the entire circuit.
CE · PET blow-moulding machine
CE conformity for PET blow-moulding machine
For PET blow-moulding machine, the applicable CE scope is determined from intended use, energy sources, safety architecture and target market. The risk assessment, technical file, testing and conformity route must be verified against the actual model.
The machine layoutLinear or rotary PET inflation
Production valueThe amount of the product is not less than EUR.
Pressure inputPre-inflation and high pressure, air tank and evacuation
Critical taskChange of shape and interference with the pre-form of the PET
Direct response to the scope
CE conformity for PET blow-moulding machine — Define the product boundary first
The location of the PET front-form feeding, heating, transfer and inflation stations in linear and rotary PET inflation machines is different. The technical file defines the number of incisions, bottle volume, rotation speed, PET front-form size, oven temperature, inflation pressure and mold weight. Mold change, neck-holding setting, and interference with the oven chain are routine tasks. Testing the machine with a single bottle format does not automatically result in the conclusion that other moulds and speeds offered for sale are safe.
High-pressure air can cause turbulence and high noise in a hose or connection failure. Inflation should not begin before the mold is completely locked; access to the door should not be provided without pressure release. Infrared heaters in the PET front-form oven are contagious, overheating and fire hazardous. Transfer wheels, mandrels and tension bars can move unexpectedly when the compressed PET front-form is removed. The safety of the mold or moving mechanism is defined when the air pressure is cut off. The impact of dirt, oil or improper pressure from the compressor line on product and machine safety is specified in the terms of use.
The first event occurring from 20 hob 2027 falls within the scope (EU) 2023/1230; national compliance with 2006/42/AT is also confirmed in Turkey due to the control of the servo and heater. EMC applies due to the control of the servo and heater. The separate LVD statement on the full machine is not automatic. The PED scope of the pressure tank, piping or system is also determined over the pressure, volume, liquid and delivery limit. The product type standards for blowing machines are also verified in the current project date.
Product profile
Technical features that change the evaluation
The following data shows why even models with the same product name can change the path of conformity.
The machine layoutLinear or rotary PET inflation
Production valueThe amount of the product is not less than EUR.
Pressure inputPre-inflation and high pressure, air tank and evacuation
Critical taskChange of shape and interference with the pre-form of the PET
Risk architecture
The main dangers to be addressed in the file
The protective, control and verification approach shall be based on the actual product cycle.
High pressure air
A hornet explosion and disconnection can cause a splash, noise, and uncontrolled movement.
Heat of the oven
Infrared heaters pose risks of burning, PET front-form ignition and panel temperature.
Tensile and transfer movement
The rod, mandrel and wheel bear the risk of compression when removing the PET front-form adhesion.
Keeping the pressure
The air remaining in the mold or tank after the power is cut must be safely discharged prior to maintenance.
The conditional law matrix
When will the regulation take effect?
A single product name doesn't give the same answer for all models.
| The subject | The situation | Product-based evaluation |
|---|---|---|
| The Commission shall adopt implementing acts in accordance with Article 21 of Regulation (EC) No 2006/42/EC and Turkey's 2006/42/AT. | YES, YES | The Directive period begins with the first supply or first service in the EU/AEA for PET inflating machines. |
| (EU) 2023/1230 | IT 'S A MESS . | In the EU/EEA, the regulatory period begins when the PET infusion machine is first supplied or first put into service. |
| The following information is provided for in Article 2 (1) of Regulation (EU) No 575/2014: | IT 'S A MESS . | Servo and oven control electronics are evaluated. |
| 2014/35/EU LVD | NO , NOT AT ALL . | The electrical hazards are assessed in accordance with Appendix I 1.5.1 to the PET infusion file 2006/42/AT; the oven subunit or electrical auxiliary sold separately is examined in its supply status. |
| 2014/68/EU PED | IT 'S A MESS . | The tank, piping and arrangement are classified by pressure-volume data. |
| The following information is provided: | IT 'S A MESS . | If there is a use or explosive gas-powder scenario in the combustion environment, the product shall also be examined. |
Standard and verification approach
- EN 422 or its current equivalent: The current project history source for mold, pressure and access hazards in inflators is examined.
- EN ISO 12100: It collects the heating, transfer, swelling and maintenance phases in a common risk method.
- EN 60204-1: It is used in electrical equipment and validation experiments according to the mechanical properties.
- EN ISO 13849-1/-2: It supports verifying the reliability of the mold lock, pressure clearance and door functions.
- EN ISO 4414: It helps me design the technical principles for the safety of pneumatic systems.
Important distinction
CE conformity for PET blow-moulding machine — Product conformity is a separate study.
ISO management system certification does not replace product-specific risk analysis, test evidence and compliance file.
The compliance work plan
In what order will the technical preparation proceed?
Do not set the bottle-format limit
PET is written on the model table, which includes the front shape, the outer surface, the volume, the speed, the oven and the pressure values.
Check the pressure chain
The component, boundary and failure behavior are determined until the compressor is discharged from the mold due to the breakdown.
Confirm the mold and oven
The door locks, mold permitting signal, temperature limit and fire scenarios are tested.
Do not complete the PED-electric proof
Pressure equipment documents, electrical measurements and EMC results are attached to the main machine file.
The instruction-report closure
Information on mold change, air quality and safe discharge is published consistent with the model label.
Product records to search for in the technical file
- Model and format matrix of PET machine
- Flue, transfer, mold and air settings
- Risk assessment based on online
- Electrical, pneumatic and cooling schemes
- Gate-stop-pressure security verification
- Experiments with heat, pressure and electricity
- Shaping and air connection instructions
- The EU Statement of Compliance is prepared for the PET inflating machine during the period of the Directive.
They 're the entries for a healthy offer .
- Linear or rotary machine type
- The volume of the bottle and the speed of the rotation
- The shape range with the PET front form
- The power of the oven and temperature control
- Pre-high swelling pressures
- Tank, compressor and pneumatic schemes
- Number of models, tests and target market
The single-format machine with the pressure-ordered documentation is not the same as the multi-cut and multi-shape line.
Internal links
Relevant category and product guides
Compare the top coverage or other similar risk architecture.
Frequently Asked Questions
CE conformity for PET blow-moulding machine — Technical answers about
Is PED mandatory in the PET inflator?
The tank, piping and arrangement are determined by the pressure, volume, liquid and delivery limit.
Does the compressor's CE cover the main machine?
No, the compressor document is stored, the weather, the connection, the molding permit signal and the final discharge verified on the machine.
Do you need a new CE for every bottle mold?
The allowed format range can be included in the technical file. New mold that exceeds the pressure, motion or protective requirement is also evaluated.
Is the oven temperature control a safety function?
In the event of excessive temperature creating fire or hazardous material degradation, independent limitation and error behaviour may be required.
Should the air be released immediately when the machine door opens?
The accessible area should not be subjected to dangerous pressure; the discharge time and time are determined by machine design.
How does high-pressure air break out in a change of shape?
The blowing line is closed and locked, the remaining pressure is discharged from the safe point and the non-pressure condition is verified; the mold motion is mechanically safe.
Technical scope and offer
CE conformity for PET blow-moulding machine — Let us clarify your technical file together.
Share the model of the machine or device, the location of use and the basic technical data. The Kayra Patent explains the path to be followed for scope analysis, technical preparation, test plan and, where necessary, approved organization coordination.
Final inspection of content and technical scope: 20 August 2026The official bases: European Commission Machinery · EUR-Lex — EU 2023/1230