ENEnglish
AZAzərbaycanca
UZO‘zbekcha
ARالعربية
FRFrançais
DEDeutsch
RUРусский
The shape and closure
The motion of the molding plate creates a large crushing volume, confirming the door and circuit function on both sides.
CE · Plastic injection-moulding machine
CE conformity for Plastic injection-moulding machine
For Plastic injection-moulding machine, the applicable CE scope is determined from intended use, energy sources, safety architecture and target market. The risk assessment, technical file, testing and conformity route must be verified against the actual model.
The machine layoutInjection of a solid, vertical, hydraulic, electric or hybrid
Main capacityThe closing force, molding plate, stroke, injection pressure and screw diameter
Access pointsOperator, opposite frame, upper area, thruster and breast area
IntegrationRobot, match control, mold modifier and product conveyor
Direct response to the scope
CE conformity for Plastic injection-moulding machine — Define the product boundary first
The technical definition includes shutting force, mold binding plate size, opening stroke, injection pressure, screwdriver diameter, processing temperature, mold weight and match circuits. Access to the opposite mold is as important as the main operator door. In large machines, the ability of a person to fully enter the mold binding plate area, resulting in a scenario of staying inside and restarting from the outside.
When the mold doors are opened, it may not be enough to isolate the movement of the bonding plate. The impeller, matching, robot, nozzle contact and screw movement must also be moved to a safe state according to the access condition. A valve failure in the hydraulic circuit can lead to the mold closing or pressure remaining in the breast area. Independent protection and safe maintenance are required for extreme heat, thermocouple error and melted plastic spillage of the heater tapes.
The mold closure, injection unit and robot take-up system are recorded according to the actual product limit. In the EU/AEA period, servo drivers enter EMC assessment of initial supply or first service of plastic injection machine; this event applies until 19 hob 2027 2006/42/EC. Machine first placed on the market or put into service after 20 hob 20 27 falls within 2023/1230 (EU) category (see also national compliance in Turkey with 2006/42/AT). Servo drives enter EMc assessment of heat control and robotic interaction during the EU / EEA period. EN 60204-1 is used for electrical refrigeration; machinery covered by LVD bearing is not fully automatically installed in typical machines. All equipment that can be fitted under normal conditions may be selected from the relevant categories of power transmission equipment or pressurized hydraulic pressure controls and must be subject to a separate safety check if applicable in accordance with Part I of Annex IX, Section 10 B of the European Chemicals Code, Annex IV, Annex X, Annex VIII, Annex V, Annex VII, or Annex II thereto, unless all necessary technical requirements are met or the vehicle's safety data are corrected in accordance to the respective categories of protection or safety related to the application of the applicable provisions of the Directive.
Product profile
Technical features that change the evaluation
The following data shows why even models with the same product name can change the path of conformity.
The machine layoutInjection of a solid, vertical, hydraulic, electric or hybrid
Main capacityThe closing force, molding plate, stroke, injection pressure and screw diameter
Access pointsOperator, opposite frame, upper area, thruster and breast area
IntegrationRobot, match control, mold modifier and product conveyor
Risk architecture
The main dangers to be addressed in the file
The protective, control and verification approach shall be based on the actual product cycle.
Eruption of the liquid
When the breast or mold is opened, the hot, pressurized polymer can cause severe burns; pressure discharge is required.
Booster and match moves
Even if the main shape appears to be stationary, auxiliary movements can create constriction in the accessible area.
Heating failure
Loss of control can cause extreme heat, material breakdown and fire; a limiting function is designed.
Buy a robot product
The robot and machine doors must have a common mode and restart behavior; separate control documents will not be sufficient.
The conditional law matrix
When will the regulation take effect?
A single product name doesn't give the same answer for all models.
| The subject | The situation | Product-based evaluation |
|---|---|---|
| The Commission shall adopt implementing acts in accordance with Article 21 of Regulation (EC) No 2006/42/EC and Turkey's 2006/42/AT. | YES, YES | The Directive period of the plastic injection machine depends on the first supply to the market or first service in the EU/EEA. Article 10 of Annex IV to the Directive 2006/42/EC is examined in the classification of injection and pressure moulding machines, which are installed or discharged by hand; 2006/42/AT is also checked in Turkey. |
| (EU) 2023/1230 | IT 'S A MESS . | The period of regulation for plastic injection machines is determined by the first market supply or first service in the EU/AEA. (EU) 2023/1230 Annex I, Section B, article 10, applies to injection and pressure-forming machines for manual loading or unloading; the date of completion is not determinative. |
| The following information is provided for in Article 2 (1) of Regulation (EU) No 575/2014: | IT 'S A MESS . | The servo, heater switching and electronic control are evaluated. |
| 2014/35/EU LVD | NO , NOT AT ALL . | Electrical hazards are assessed in accordance with Appendix I 1.5.1 to the plastic injection machine file 2006/42/AT; the robot control or the electrical device supplied alone is assessed in its supply status. |
| 2014/68/EU PED | IT 'S A MESS . | Accumulator and pressure equipment are classified by technical values. |
| The following information is provided: | IT 'S A MESS . | If there is a specific design for the fuel additive, gas or explosive environment, the scope shall be investigated. |
Standard and verification approach
- EN ISO 20430: Plastic and rubber cover the safety requirements of injection molding machines.
- EN ISO 12100: It assesses the risks of molding, melting, maintenance and automation systematically.
- EN 60204-1: The machine is used for electrical equipment and verification tests according to product specifications.
- EN ISO 13849-1/-2: It supports performance verification of door, valve and robot security functions.
- EN ISO 14119: It helps to select the locking patterns on the mold doors and to resist decommissioning.
Important distinction
CE conformity for Plastic injection-moulding machine — Product conformity is a separate study.
ISO management system certification does not replace product-specific risk analysis, test evidence and compliance file.
The compliance work plan
In what order will the technical preparation proceed?
Not setting the machine-stop limit
The configuration offered for sale is fixed by the closing force, pattern and process values.
Don 't analyze the online tasks
Parts into the mold, automatic production, sampling, breast cleaning and mold change are examined separately.
Verify the gate and hydraulic function
Interruption, valve error behavior and restart scenarios are tested on each access side.
Collecting the heat-electrical evidence
Excessive temperature, protective conductivity, insulation, EMC and control parameters are recorded.
Do not close the serial file
The mold boundaries and the robot connection are processed in instructions; the statement and product label show the same model.
Product records to search for in the technical file
- Injection machine model and capacity matrix
- Sculpture board, door, breast and pusher drawings
- Risk assessment based on online
- Electrical, hydraulic and heating schemes
- Gate-valve security verification report
- Record of temperature, pressure and electrical tests
- Operating instructions with change of pattern
- The EU Statement of Compliance is prepared for the plastic injection machine during the regulatory period. The plastic injection machine statement is attached to the label and technical file with type, model and serial identity.
They 're the entries for a healthy offer .
- Type of machine and shutdown force
- Stroke of opening by the size of the molding board
- Injection pressure and temperature range
- Shaped weight and match options
- Robot and conveyor integration
- Hydraulic-electric schemes
- Existing tests, number of models and target market
In two similar machines with a shutter speed, vertical installation, robot and counter-access can change the scope of operation, which becomes clear when the proposal, circuits and actual protective order are seen.
Internal links
Relevant category and product guides
Compare the top coverage or other similar risk architecture.
Frequently Asked Questions
CE conformity for Plastic injection-moulding machine — Technical answers about
Do you need two-door circuits in an injection machine?
Access side and product standard are evaluated, and independent or backup measures may be required for the operator and counterparty in large-scale bonding plate areas.
Is the robot's CE document enough for the main machine?
No. Robot proof is the input component; the input into the mold, mode selection, common position, and the cell restart approval are verified in the final system.
How is the mold included in the CE file?
The permitted size, mass, connection and match range are defined, and the drawing and risk interface are stored in the file if the manufacturer has specified a specific pattern.
If there's no hydraulic risk in an electric machine, will the process be shortened?
Certain circuit risks may be reduced, but the servo movement, mold access, heater and functional safety evidence must be completed again.
Is it mandatory to use EN ISO 20430?
Harmonization is a standard voluntary conformity path; in the absence of use, it is demonstrated in detail how the basic requirements are met in an equivalent manner.
Does manual installation affect your particular category decision?
Plastic injection and pressure-forming machines, which are manually loaded or unloaded, are specifically inspected under Addendum IV or Addendum I to Regulation Part B.
Technical scope and offer
CE conformity for Plastic injection-moulding machine — Let us clarify your technical file together.
Share the model of the machine or device, the location of use and the basic technical data. The Kayra Patent explains the path to be followed for scope analysis, technical preparation, test plan and, where necessary, approved organization coordination.
Final inspection of content and technical scope: 20 August 2026The official bases: European Commission Machinery · EUR-Lex — EU 2023/1230